DF-101S Digital Heat-gathering Magnetic Stirrer & Water Bath 300°C Thermostat. DF-101S Digital Collector Magnetic Heating Stirrer Laboratory Water Bath Oil Bath Dual-Use Constant Temperature Stirrer Tank Pot 110V. Temperature range: room temperature to 300 ° C. Temperature control accuracy: = ± 1? Working size (mm): f200 100.Widely used in distillation, drying, concentration and impregnation of chemicals or biological products, can also be used for constant temperature heating of oil baths and other temperature tests. It is an indispensable tool for. Biology, genetics, viruses, aquatic products, environmental protection, medicine, health, biochemical laboratories, analysis rooms, epidemic prevention, petroleum, and chemical education. High-quality 304 stainless steel liner, using stamping technology, one-time molding, water bath heating, oil bath heating and dry burning.
High quality dual switch, separate control of power heating, convenient and fast. High-quality temperature control instrument with clear and intuitive readings, simple operation with touch keys, precise temperature control, and good experimental results. Using high-quality DC motor, low noise, stable speed regulation, no vibration, can set temperature and temperature display, can be used for long-term heating, and the digital display is intuitive and accurate. Stainless steel explosion-proof heating tube, fast heating speed, uniform temperature, round and safe design.
Stirrer made of high-quality magnetic steel, high temperature resistance, wear resistance, chemical resistance, strong magnetic. Turn on the power and the cup is ready. Open the stainless steel container lid, place the cup in the middle of the stainless steel container, add thermal oil or silicone oil to the stainless steel container to the proper height, and place the stir bar in the cup solution.
Turn on the power switch, the indicator light is on, close the heating switch, and the temperature digital display light is on. At this time, the displayed value is the actual temperature in the pot. If you want to stir, put the stirrer in the cup solution, rotate the speed control potentiometer clockwise, and stir the speed from slow to fast. Adjust to the required speed.
When heating, connect the temperature sensor probe, clamp the probe on the bracket, move the bracket to insert the temperature sensor probe into the solution no less than 5 cm, but it cannot affect the stirring. Turn on the temperature control switch, set the required temperature, press +, -on the temperature controller to set the required constant temperature temperature, the digital display value on the meter head is the actual temperature in the cup, the heating stops, and the automatic constant temperature.
Set temperature: Press the SET button to flash the data on the lower digital tube (normal temperature measurement in the upper row) to indicate that the meter has entered the temperature setting state. Key to increase the value, press? To decrease the value, and continue to increase The setting value of the key or decrease key will change rapidly.Press the SET key again and the meter will return to normal working state. If the stirrer jumps during work, please turn off the power and then turn it on again. The speed can be changed from slow to fast, and adjustment can resume normal work. To ensure your personal safety, please use a three-phase safety socket, and it must be properly grounded during use.
The instrument should be kept clean and tidy, and the power should be cut off if it is not used for a long time. Turn off the switch to avoid accidents.
When the stainless steel container is not filled with heat-conducting oil and the temperature sensor is not connected, please do not turn on the temperature control switch to avoid damage to the heating pipe and the thermostat. A metal tube is installed in the pot as a temperature sensor. Please do not collide to avoid temperature failure. The bottom of the oil must ensure that the heating tube and sensor are immersed in the oil.1 DF-101S collector magnetic stirrer. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business.
A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it's non-workdays, please kindly be patient and wait till Monday. BI-ZTCYT-870 DF-101S Digital Collector Magnetic Heating Stirrer Laboratory Water Bath Oil Bath Dual-Use Constant Temperature Stirrer Tank Pot 110V Description Name: Collecting magnetic stirrer Model: DF-101S Temperature range: room temperature to 300 ° C Temperature control accuracy: ± 1 Voltage: 110v Speed: 0-1600 rpm Mixing power: 40W Heating power: 400W Stirring capacity: 2000 ml Working size (mm): 200 100 use: Widely used in distillation, drying, concentration and impregnation of chemicals or biological products, can also be used for constant temperature heating of oil baths and other temperature tests. It is an indispensable tool for biology, genetics, viruses, aquatic products, environmental protection, medicine, health, biochemical laboratories, analysis rooms, epidemic.
The item "220V DF-101S Digital Heat-gathering Magnetic Stirrer Mixer Thermostat Hotplate b" is in sale since Thursday, June 11, 2020. This item is in the category "Business & Industrial\Healthcare, Lab & Dental\Medical & Lab Equipment, Devices\Lab Mixers, Shakers & Stirrers\Magnetic Stirrers & Hotplate Stirrers". The seller is "save-lots4u" and is located in Rowland Heights, California.
This item can be shipped to United States.